1:87 model building

To operate small 3-6 V motors at a higher voltage, this PWM was developed. The circuit is suitable e.g. for controlling special functions in RC model making and railway model construction.

Universal soldering station with 48 W and fine soldering tip. Ideal for model making and fine electronic soldering.

ER600L speed regulator, 0.37 grams, brake light and reverse output, 2.7 - 5.5 Volts

Switching channel module FM, 5 channels for individually switching on/off, 500 mA each.

micromotor, nominal voltage (V): 3, no-load speed (rpm): 40000, weight (g): 0.47, dimensions diameter / length (mm): 6 x 14, axle diameter (mm): 0.8

Universal gear kit with motor for voltages 0.3 - 6 V and 4 adjustable ratios of 9: 1/27: 1/81: 1/243: 1. Output shaft revolutions: 2.5 - 720 U / m, dimensions 36 x 38 x 26 mm

Drive for 1:87 tractors, machines and other slow moving vehicles. Translation: 1: 494. Dimensions: 22 x 12 x 9 mm, 4.5 grams, kit

Micro gear units G95B for 1:87 truck drives and drive for 1:87 truck models, winches, special functions and more. Translation: 1:95. Dimension: 20 x 12 x 9 mm, 4.5 grams

brass gear unit 1:90 with brass gear wheels, dimensions 15 x 6 x 6 mm (without motor), assembled, with motor M705 Manual

Micro gear units G95 for 1:87 truck drives and drive for 1:87 truck models, winches, special functions and more. Translation: 1:95. Dimension: 20 x 12 x 9 mm, 4.5 grams

Screw made of brass, module M0.2, internal hole 0.8 mm, L: approx. 3.5 mm, Diameter: 2.8 mm

Gear Z181, Number of Teeth: 18, Module: 0.2, Bore: 1 mm (+0.02 mm), Height: 1 mm (-0.02 mm), Serration: straight, Material: Brass

Gear, Number of Teeth: 15, Module: 0.2, Bore: 1 mm (+0.02 mm), Height: 1 mm (-0.02mm), Serration: Straight, Material: Brass

5 x S18JST: One of the world's smallest servos! This servo is distinguished by the smallest dimensions (13.5 x 16 x 6 mm) and an extremely low weight (1.8 g). Therefore it is extremely well suited for the smallest models, special functions and models that offer little room for the installation of a servo due to their shape.

With tires and rims, for 2 spokes: 14.5 and 16.5 mm (distance between the center points of the tires). For car and RC systems. Suitable for vehicles such as M-Class, Golf, Sprinter, etc.

Suitable for front, rear and double wheels. Dimensions: Inner diameter 6.7 mm, outer diameter 12.3 mm, width 3.2 mm.

4-unit set of ball bearings, sealed, Inside: 1.5 mm, Outside: 4 mm, Height: 2 mm

NiMH rechargeable battery 300 mAh, 1.2 V, weight: 5 g, diameter 8.5 mm, height: 42.5 mm, replacement battery for car system vehicles

Lithium-polymer battery with 110 mAh and integrated deep discharge protection, 5 cm cable, dimensions: only 21 x 12 x 5 mm, 3.7 V, making it ideal for small trucks and vans.

USB-LIPO-LADEPLATINE for simultaneous charging of 2 single-cell batteries (from 10 mAh).